Trick or Treat
Designer Jamie Hogsett

Skill Level Intermediate

Materials

Trios Trick or Treat (Citrine, Yellow Lemon Quartz, Black Onyx)
Silver 14x20mm Skull and Bones Toggle - 1 set
1 1/2" Silver 24-gauge Head Pins - 48 pcs
2mm x 2mm Sterling Silver Crimp Tubes - 16 pcs
3mm x 3mm Sterling Silver Crimp Tubes - 6 pcs
5mm Silver Crimp Bead Covers - 22 pcs
6mm Jet/Silver Rhinestone Rondelles - 4 pcs
7mm Crystal/Silver Rhinestone Rondelles - 4 pcs
10mm Crystal/Silver Rhinestone Rondelles - 4 pcs
10mm Silver Skull Beads - 4 pcs
4mm Half Coated Silver Czech Faceted Rounds - 72 pcs
6mm Medium Jonquil Czech Faceted Rounds - 8 pcs
10mm Medium Topaz Czech Faceted Rounds - 4 pcs
13x10mm Topaz/Black Mix Faceted Ovals - 4 pcs
6x8mm Dark Topaz Faceted Drops - 4 pcs
5mm Black Czech Faceted Diamonds - 4 pcs
10mm Jet Black Czech Faceted Fancy Cut Rounds - 4 pcs
14mm Jet Black Czech Faceted Fancy Cut Rounds - 4 pcs
6x9mm Jed Black Czech Faceted Rondelles - 8 pcs
14mm Orange with Stone Czech Faceted Rondelles - 4 pcs
6mm Dark Topaz with Brown Iris Czech Faceted Tubes - 8 pcs
10mm Black with Faux Stone Czech Cathedral Barrels - 4 pcs
8mm Black with Silver Ends Czech Cathedral Barrels - 4 pcs
10mm Red Spiderweb Agate Rounds - 8 pcs
12mm Red Spiderweb Agate Rounds - 4 pcs
18mm Grey Spiderweb Agate Rounds - 4 pcs
25mm Grey Spiderweb Agate Coins - 4 pcs
15-20mm Grey Spiderweb Agate Oval Twists - 4 pcs

Tools

Cutters
Bead Crimping Pliers
Mighty Crimper
Bead Stoppers

Instructions

Finished Size: 20"




Step 1: Use 1 head pin to string one 6mm Dark Topaz with Brown Iris Czech Faceted Tube and form a wire wrapped loop. Repeat seven times to make a total of eight 6mm tube dangles. Repeat entire step once to create eight dangles using 10mm Red Spiderweb Agate Rounds.

Step 2: Use 1 head pin to string one 10mm Black with Faux Stone Czech Cathedral Barrel and form a wire wrapped loop. Repeat three times to make a total of four 10mm cathedral barrel dangles. Repeat entire step four times to create four dangles of each of the following beads: 13x10mm Topaz/Black Mix Faceted Ovals, 10mm Jet Black Czech Faceted Fancy Cut Rounds, 8mm Black with Silver Ends Czech Cathedral Barrels, and 10mm Medium Topaz Czech Faceted Rounds.

Step 3: Use 1 head pin to string one 6mm Medium Jonquil Czech Faceted Round, one 6mm Jet/Silver Rhinestone Rondelle, and one 6mm Medium Jonquil Czech Faceted Round. Form a wire wrapped loop. Repeat three times to form a total of four jet rondelle dangles. Repeat entire step once using one 6x9mm Jed Black Czech Faceted Rondelle, one 7mm Crystal/Silver Rhinestone Rondelle, and one 6x9mm Jed Black Czech Faceted Rondelle to form four crystal rondelle dangles.

Step 4: Use 1 head pin to string one 6x8mm Dark Topaz Faceted Drop, 1 Skull Bead, and one 5mm Black Czech Faceted Diamond. Form a wire wrapped loop. Repeat three times to form a total of four skull dangles.

Step 5: Use 6" of Citrine wire to string one 2mmx2mm crimp tube, 1 tube dangle, one 10mm cathedral bead dangle, 1 skull dangle, 1 topaz/black mix oval dangle, one 10mm red spiderweb agate round dangle, and 1 crystal rondelle dangle. Pass the wire back through the tube, leaving a loop of wire that hangs about 3/8" below the crimp tube, and crimp. Cover the tube with a crimp cover. Use the other end of the wire to string 1 grey spiderweb agate coin and one 2mmx2mm crimp tube; pass back through the tube, leaving a 4mm loop, and crimp. Cover the tube with a crimp cover Repeat entire step three times to form a total of four coin pendants.

Step 6: Use 6" of Yellow Lemon Quartz wire to string one 2mmx2mm crimp tube, one 10mm Medium Topaz Faceted Round dangle, one 8mm cathedral barrel dangle, 1 tube dangle, 1 jet rondelle dangle, one 10mm Jet Black Czech Faceted Fancy Cut Round, and one 10mm red spiderweb agate round dangle. Pass the wire back through the tube, leaving a loop of wire that hangs about 3/8" below the crimp tube, and crimp. Cover the tube with a crimp cover. Use the other end of the wire to string 1 grey spiderweb agate oval twist and one 2mmx2mm crimp tube; pass back through the tube, leaving a 4mm loop, and crimp. Cover the tube with a crimp cover Repeat entire step three times to form a total of four oval twist pendants.



Step 7: Cut 26" of Citrine wire. Cut 26" of Yellow Lemon Quartz wire. Cut 26" of Black Onyx wire. Use all three wires to string one 5mm Black Czech Faceted Diamond, 1 coin pendant, and one 5mm Black Czech Faceted Diamond to the center of the wires. Place a Bead Stopper on one side of the pendant.

Step 8: Use all three wires to string one 18mm grey spiderweb agate round. Use the Citrine wire to string six 4mm Half Coated Silver Czech Faceted Rounds. Repeat with the Yellow Lemon Quartz and the Black Onyx wires. Use all three wires to pass through the spiderweb agate round again. Use all three wires to string one 12mm red spiderweb agate round, 1 oval twist pendant, one 14mm Jet Black Czech Faceted Fancy Cut Round, one 10mm Crystal/Silver Rhinestone Rondelle, and one 14mm Orange with Stone Czech Faceted Rondelle.



Step 9: String one coin pendant. Repeat Step 8. Place a Bead Stopper on the wires.

Step 10: Remove the Bead Stopper used in Step 7. Repeat Steps 8 and 9 on the other side of the center pendant.

Step 11: Cut four 8" pieces of Citrine wire. Repeat with the Yellow Lemon Quartz wire and the Black Onyx wire.

Step 12: Remove one Bead Stopper. Use all three wires to string one 3mmx3mm crimp tube to the orange faceted rondelle. Place the ends of two Citrine wires, two Yellow Lemon Quartz wires, and two Black Onyx wires in the crimp tube, and crimp. Cover the tube with a crimp cover.

Step 13: Braid the three Citrine wires together for about 5 1/2". Place a Bead Stopper at the end of the braid. Repeat using the three Yellow Lemon Quartz wires and the three Black Onyx wires.

Step 14: Braid the three braids together for 4 1/2". Hold the wires together where the braid ends, remove all three Bead Stoppers and use all nine wires to string one 3mmx3mm crimp tube. Crimp the tube and cover it with a crimp cover. Use cutters to trim two Citrine wires, two Yellow Lemon Quartz wires, and two Black Onyx wires.



Step 15: Use the remaining three wires to string one 3mmx3mm crimp tube and the bar (bone) half of the clasp; pass back through the tube and crimp. Cover the tube with a crimp cover.

Step 16: Repeat Steps 12-14 for the other half of the clasp. Use all three wires to string 1 coin pendant. Repeat Step 15, using the ring (skull) half of the clasp.




Projects not intended for children under the age of 13. The information on this instruction sheet is presented in good faith, but no warranty is given, nor results guaranteed. Soft Flex® Company disclaims all liability from any injury to anyone undertaking the construction of this project as a result of improper safety precautions.